BEF milling machines for concrete and screed floors
We offer a wide range of powerful milling machines to level the floor surfaces and prepare them optimally for further processing.
Cutter milling machines
When milling, the surface of the soil is removed by rotating cutters. A distinction is made between cutters milling machines (e.g. star cutters) and chisel milling machines for the deep removal of uneven soils or for soil rehabilitation. Our powerful cutter milling machines are characterised by a finer milling pattern, while chisel milling machines should be used for coarser and deeper removal of unevenness (from approx. 1.5 cm upwards).
When milling with cutters, cutters are loosely mounted on a drum shaft and act through rotation very evenly on the surface. It is important that the tips can just still act on the substrate. This results in an even flaking of the surface with a much finer milling pattern than when using chisel cutters. When it comes to removing irregularities such as protrusions, markings and depth removal from concrete and screed floors, our milling cutters are ideal for this.
All of our milling machines can be equipped with carbide cutters or peeling cutters. This selection of cutters depends on the subsurface and the aim of the work to be carried out. 5-point carbide-tipped cutters, for example, roughen the ground evenly depending on the working depth, while 8-point carbide-tipped cutters with a smaller working depth can also be referred to as fine milling rotors. Peeling cutters are mostly used for softer surfaces or to remove coatings.
The front-mounted milling drum guarantees uniform milling results
The exceptional milling results are supported by permanent 4 x 4 all-wheel drive, which enables even and directionally accurate milling of surfaces. The front-mounted drum has the advantage of being able to com-pensate for uneven ground, ensuring uniform depth removal.
The low centre of gravity of the milling machines also supports smooth running and a uniform milling pattern.
The advantages of milling are its depth capabilities and the facility to compensate out considerable differences in height that are unwanted on site.
Our highly-skilled application technology advisors will be happy to guide you.
Please feel free to contact us at any time for further assistance or intense consulting. - To contact form
BEF concrete & screed milling machines
-
BEF 201
Concrete milling machine for small and medium areas
More Information -
BEF 201V
Reliable, robust petrol-powered concrete milling machine for small to medium-sized areas
More Information -
BEF 204
Lightweight screed milling machine with integrated edge milling
More Information -
BEF 250
Robust electrically operated concrete and screed milling machine for medium areas
More Information -
BEF 250V
Robust concrete and screed milling machine with combustion engine for medium areas
More Information -
BEF 320
Milling machine with high milling performance even under tough operating conditions
More Information -
BEF 320V
Milling machine with high milling capacity also with petrol drive
More Information -
BEF 400RC - NEU
Remote-controlled high-performance milling machines with great floor coverage capabilities
More Information
Pre-equipped and unequipped rotors
... enable innovative milling technology for small and large areas
Drum with 4 shafts (702132)
w/o equipment
Drum with 8 borings for axles = longer lifetime and less costs per m²
Drum (704361)
With 5-point carbide-tipped cutters, Ø 42 x 6 mm
Drum with exchangeable bushes for axles = longer lifetime and less costs per m²
Drum (704422)
With peeling cutters, Ø 42 x 22 mm
Drum with 8 borings for axles = longer lifetime and less costs per m²
Drum with 4 shafts (704551)
Ø 10 mm, without cutters
Drum (704552)
With 5-point carbide-tipped cutters, Ø 42 x 6 mm
Drum (704738)
With 5-point carbide-tipped cutters, Ø 42 x 6 mm, cowshed preparation
Drum with special equipment for scarifying floors in cowsheds
Drum (707220)
Without cutters, 4 shafts
Drum (707221)
With 8-point carbide-tipped cutters, Ø 80 x 8 mm
Drum with exchangeable bushes for axles = longer lifetime and less costs per m²
Drum (707222)
With peeling cutters, Ø 80 x 20 mm
Drum with exchangeable bushes for axles = longer lifetime and less costs per m²
Drum (717280)
With 8-point carbide-tipped cutters, Ø 80 mm
Drum (717281)
With peeling cutters, Ø 80 mm
Drum (717282)
With 8-point carbide-tipped cutters, Ø 80 mm, fine milling motor
Drum with 6 shafts (717283)
Without cutters, Ø 22 mm
Drum with cutting disc cpl. (717631)
Incl. 66 diamond cutting discs with 4 mm washers
Drum 8-pt. tungst. carbide tipped cutters cpl. (717700)
